14 foot starcraft project for this year

TinBoats.net

Help Support TinBoats.net:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Prawndave

Active member
Joined
Jun 1, 2017
Messages
27
Reaction score
0
Not sure exactly what model this is as the plate is worn clean. I know it's rated for a 30 horse and I think 900 plus lbs. Picked it up with the trailer for 500 and a 96 merc 15 horse for 650. Should be a great little fishing boat when I'm done.
 

Attachments

  • 20170608_181340.jpg
    20170608_181340.jpg
    106.9 KB · Views: 4,831
  • 20170613_195120.jpg
    20170613_195120.jpg
    121.6 KB · Views: 4,831
Things are happening
 

Attachments

  • 20170702_120539.jpg
    20170702_120539.jpg
    98 KB · Views: 4,763
  • 20170702_120546.jpg
    20170702_120546.jpg
    87.3 KB · Views: 4,763
Mostly a flat floor with some decking in the front and back... going to keep it pretty simple for now since I really just want to get out on the water. Finished the transom and started framing the floor yesterday. Replaced some rollers and the lights on the trailer too.
 

Attachments

  • 20170702_184117.jpg
    20170702_184117.jpg
    87.2 KB · Views: 4,733
  • 20170702_184134.jpg
    20170702_184134.jpg
    96.1 KB · Views: 4,733
  • 20170702_184109.jpg
    20170702_184109.jpg
    106.9 KB · Views: 4,733
Some more framing started...still have to add all the supports and some cross members.
 

Attachments

  • 20170703_164723.jpg
    20170703_164723.jpg
    101 KB · Views: 4,701
What experience does anyone have with rubber flooring .... one im considering is mostly black but has a matte finished with a kind of a grey fleck to it.
Worried about it being too hot for the boy to crawl around on but I really like the idea of clean up. The front and back deck will likely be carpet.
In other boats I have had that shiney black runner stuff on the bottom of the boat but I'm hoping this stuff would be much much better and easy to cleanly install.
 
Nice boat.
Roller trailers are not usually the best for aluminum boats.
 
No ...eventually it'll get stripped down and cleaned up too and I'll throw some bunks on it. With the amount of time I work and since I sold my other set up to buy this it's now becoming a rush to get it in the water.
 
Almost ready for the floor to go in ... really stiffened things up.
 

Attachments

  • 20170708_150209.jpg
    20170708_150209.jpg
    96.8 KB · Views: 4,593
  • 20170708_150200.jpg
    20170708_150200.jpg
    105.9 KB · Views: 4,593
Getting closer to being on the water everyday ....just have to decide what I'm doing with the flooring then build some decks and pop in the stereo.
 

Attachments

  • 20170709_154829.jpg
    20170709_154829.jpg
    65.9 KB · Views: 4,566
  • 20170709_154735.jpg
    20170709_154735.jpg
    77.6 KB · Views: 4,566
Had to break down and purchase a new cover ...not having a garage and all this rain is really annoying
 

Attachments

  • 20170713_202757.jpg
    20170713_202757.jpg
    60.3 KB · Views: 4,496
it looks like a seafarer by starcraft. Don't go to high on the floors, it will be real unstable, i have a starcraft 14 footer also and had to lower mine. Mine is older then yours it's a 1958 modified ski champ. The 15 horse will move it nicely i have a 20hp johnson on mine. The picture with the carpeted deck was before i changed it, that was the way it came and it was unusable like that, felt like the boat would roll over, very unstable, the other picture is the change i did and took it out fishing 100 percent better and stable, note all three seats are right in the center.
 

Attachments

  • Renistalled.jpg
    Renistalled.jpg
    51.7 KB · Views: 4,486
  • Boat 3.jpg
    Boat 3.jpg
    50.4 KB · Views: 4,486
I am working on a 16' Starcraft Seafarer. Mine is a 1981 and appears very similar to yours in floor /rib design and style. Mine is only rated for 5 people and 780lbs from what little I could read on the faded placard. I believe it's only rated for 35 or 40hp too. I'm just going to put a 15 or 20hp on it because I don't plan on using it for big water. If my needs evolve down the road, I'll save some more money and trade up for a bigger motor but for now I think 15 to 20 will be plenty. Many of our mountain lakes here in AZ won't even allow gas motors. Those that do usually limit it to 10hp.

The trailer that I got with the boat, I think, was homemade. It was a tilt style trailer with a handle in the front so you could dump the boat off easily. I put a pin through the frame to lock it in. I also had a friend help me weld some Bunk Bolster Brackets (C.E. Smith brand) onto the trailer to mount bunks.

Good luck with the project. I laughed because most of my pictures come in sideways or upside down too. This Forum software must be from 1996.

Link to my project here: https://www.forum.tinboats.net/viewtopic.php?f=21&t=43099
 
The height of the seat won't really change ..basically just sheeting over that stock seat for some storage in the back and front ...hoping to maybe get the flooring completed and get a little test ride in before I get much more done.
 
Well I couldn't find a rubberized material that wasn't black and stumbled across enough carpet to do the entire boat and decks for 50 bucks ...got the floor done.
 

Attachments

  • 20170715_115748.jpg
    20170715_115748.jpg
    78.3 KB · Views: 1,837
  • 20170715_115452.jpg
    20170715_115452.jpg
    51.5 KB · Views: 1,837
Looks good. Is there a chance you measured the width in the middle before taking out the bench to see if it's wider without it.
 
Ya it didn't change at all ...before the floor went in in was a bit worried about the flexing but I attached each cross member to the ribbing 2 or 3 Times and it's stiffer now than before the seat came out ....i still plan to brace the sides to the floor also using the bracing as rod holders.
 
Bad pic but I started to frame the back seating deck and the little bump out for the stereo and fish finder and maybe switches.
 

Attachments

  • 20170715_164242.jpg
    20170715_164242.jpg
    84.4 KB · Views: 1,819
Not much time lately to get anything done but I slapped in the stereo and two of the speakers this morning.
 

Attachments

  • 20170722_105133.jpg
    20170722_105133.jpg
    64.6 KB · Views: 1,782

Latest posts

Top