Just got a "new" old boat. I think it's a 16' Lone Star, but nothing really matches up.

TinBoats.net

Help Support TinBoats.net:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I plan on running mine with a 8 HP Mercury. Everyone on here has mentioned to stay away from the single cylinder 4 strokes. Eight Horse power should be plenty for getting around the lake. The plate on my 14 footer says Ten HP max.
 
Finding some more information. Got the holes patched up too.

2cak9ZUh.jpg


Here's the hole in the bottom of the boat, before I started scraping off the JB weld that was there.

dDmhWlSh.jpg


This was easy enough to fix once I got the boat up on the sawhorses and started cleaning off the old paint.

RJoFjIvh.jpg


You can kinda see the big dent right there on the riveted seam, but

QSVv5aPh.jpg


Took a lot more cleaning to get the panel ready to weld, but it cleaned up fine.

21N7EHrh.jpg


Next up is the float test. Gonna go float it on a local pond to make sure it doesn't leak, and if it does, we'll mark them up and I'll swell rivets or replace them if I need to.
 
Stainless wire brush, make sure your patch is at least 3/8" longer than the crack you're patching, and wipe with acetone before welding. Same rules for using "alumi-weld" too, you could braze the patch on with a (admittedly large) propane torch, and it'd work just as good as long as your patch fits the curves and distortions in the panel well.

Never use a flap disk or sandpaper, they are most likely aluminum oxide grit and are just going to add to the oxide layer you're removing, and never a carbon steel brush, as it'll embed iron and iron oxides into the aluminum and both will cause trouble, during the weld and after welding.
 
Finding some more information. Got the holes patched up too.

2cak9ZUh.jpg


Here's the hole in the bottom of the boat, before I started scraping off the JB weld that was there.

dDmhWlSh.jpg


This was easy enough to fix once I got the boat up on the sawhorses and started cleaning off the old paint.

RJoFjIvh.jpg


You can kinda see the big dent right there on the riveted seam, but

QSVv5aPh.jpg


Took a lot more cleaning to get the panel ready to weld, but it cleaned up fine.

21N7EHrh.jpg


Next up is the float test. Gonna go float it on a local pond to make sure it doesn't leak, and if it does, we'll mark them up and I'll swell rivets or replace them if I need to.
BTW, can you grind that flat or smooth it out in any way or will it weaken the fix ? I don't mean to offend , but think it looks like a very talented nice weld job. But , I'm not really knowledgeable about these things and want to know the details ??
 
Nope. The skin of the boat is too thin to grind that down, that's another layer welded over the crack. You could grind out the crack, drill both ends, and weld the (very thin) aluminum hull, but you'd be asking for problems.

You could smooth it out with a sanding block and some elbow grease but there isn't any need to, it's not like it's gonna go more than 10MPH at any point in it's life.
 
Nearly 18 years now. Before I became a high school teacher I did aluminum casting repair for about half my business in the machine shop. Fixed a few boat hulls, trying to treat them like regular sheetmetal always resulted in a comeback. Put a patch over the crack instead, and the repair lasts.
 
When your dealing with old contaminated stressed out aluminum a patch is a wise choice. I have a small crack on my boat and it had been repaired with 650K epoxy and fiber tape. The patch was on the boat when my wife's brother bought the boat. So I know it was at least 5 years old and it did not leak. Kind of sitting on the fence on making repair. Weld or go back with same patch? By trade a Tig Welder. Everything from military planes to military ships. Over 20 years experience. Knowing how old aluminum sometimes does not work out as planned I am not sure which route to take. After reading your post kind of thinking about welding the crack.
 
Nope. The skin of the boat is too thin to grind that down, that's another layer welded over the crack. You could grind out the crack, drill both ends, and weld the (very thin) aluminum hull, but you'd be asking for problems.

You could smooth it out with a sanding block and some elbow grease but there isn't any need to, it's not like it's gonna go more than 10MPH at any point in it's life.
BTW, I'm no welder but have been studying lately to learn and even have my welder , a line on a bottle of Argon and plenty of alum scrap for practice w/good material for framing my floor , boxes and such. I'll be spool gunning or mig welding it but your work looks so nice I wonder :
Is that tig welding you've done ??
 
Took some photos this morning.

zAxL2jCh.jpg


We got the boat on the trailer, but haven't adjusted anything on the trailer yet.

I got a big sheet of stainless steel recovered from a countertop at the same time, so I gotta get that cut down and deliver it to my workshop today. That's what's laying in the boat here.

wsOYtawh.jpg


All the details seem to point to it being the "Commander" model but little details are different.

jH0L1Zhh.jpg


It definitely is a Lone Star boat, though, you can barely see it in this photo if you know what the logo looks like. it took a lot of sitting and staring at it to finally make out what it says.

Gtx1G9dh.jpg


Once the title is transferred, I need to fix this crack in the bottom. It's got two other welded patches already so I know that the welding won't be an issue, but there is one big dent right on a rivited seam that has me worried.

dDmhWlSh.jpg


The crack above is where something got dropped inside the boat, but it's been patched in the past with some tarry black stuff. I will have to get it all cleaned up, run the saw through the crack to clean the edges, and then weld it back up...not opening the crack up will mean I'll never get the dent smoothed back. The dent is about the side of a baseball, the crack is about two inches long or so.

n60A0L8h.jpg


Oh, and the transom is rotten, I'll have to change that board out.
Don’t know if this helps. It’s from a Lone Star 1962 sales brochure.
 

Attachments

  • F18E27FE-479A-4AF0-8C50-52735A791936.jpeg
    F18E27FE-479A-4AF0-8C50-52735A791936.jpeg
    155.1 KB · Views: 0
Yes, it was tig welded.
Nice job welding. I wish you were my neighbor. I have a 1984 Monark that doesn’t leak but it has some patch work I’d like to redo.
Probably a dumb question but have you seen any signs of a serial number.
Here in Texas you can look up owner history on any boat or motor on the parks and wildlife website.
There’s also a way to title an abandoned boat. Or homemade if it passes their inspection done by a game warden.
 
You can always put an pre 85 motor on there, they were rated from the head instead of the prop so the HP at the prop could be between 5-10% off from the head, meaning you could put a 15 on there and still achieve 12 at the prop, still within legal limits - although you have to convince anyone trying to ticket you (as if they really would) that 15hp in 1985 is 12hp today.
 

Latest posts

Top