Recent content by eeshaw

TinBoats.net

Help Support TinBoats.net:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. E

    How to adjust free play in steering wheel?

    Did you check to see if the "hair pin" clip is in place? It holds the end of the cable inside the rotary helm, keeping it stationary.
  2. E

    portable transducer idea

    I've got a cable operated trolling motor that has the transducer mounted to it so I can just sit or stand and work it side to side.
  3. E

    Installed a Tachometer

    I bought some used gages for my Mako project. I won't do that again. They're pretty brittle and you have to be really careful with installation or they can break. I'd like to be able to verify the accuracy of the tachometer with the engine running but I think that would require a "tiny" tack...
  4. E

    Impact of Prop Pitch on Trolling Speed

    If you want to troll slower get a drift sock to use. That way you can keep your current prop that works for your boat most of the time.
  5. E

    Do it yourself honing?

    Not telling you what to do but my experience with you doing this is leave it to a professional. The hones with the round balls are meant to be glaze breakers. The hones with three or four stones on them are what you're wanting to use to establish a cross-hatch for oil retention purposes...
  6. E

    Rocker switch cover

    Without seeing your layout I'd suggest that you get a radio cover, one of those type that you pull out and then flips down to cover the face plate. Might work for you.
  7. E

    Outboard Mounting Bolts - No washers on Transom Bracket Side?

    I just mounte a 125 mercury to my boat and I didn't use any washers on the bracket side of the transom. Big washers are all on the inside. I also have a reinforcement bar on the top inside of my transom to help distribute the load too.
  8. E

    Mercury 60HP Bigfoot on Pontoon Prop Pitch

    Most of the Bigfoot engines I've seen came with 4 blade props on them.
  9. E

    My 2022 SunTracker 22DLX Thread

    I believe it does but you should research it for yourself. I'm very happy with mine.
  10. E

    My 2022 SunTracker 22DLX Thread

    You're going to like the Vessel View. I have it for my jon boat but I splurged and got the black box setup so I wouldn't have to contend with connectivity issues. That thing can do so much it's just ridiculous.
  11. E

    What trolling motor upgrade

    I've got to say that the asking price for the Ghost and others is off the chart for what you get and I can't justify the cost. I thought I payed a lot for the Motorguide Xi5 I have but compared to what's being pedaled now it was a bargain. It might have been purchased used but it's been a...
  12. E

    Braided vs monofilament/ Sorry I originally posted this in the wrong place

    My bigger rod is about the same as what you're rigging. I do a lot of flat head fishing and get some really good size ones, 50+ lbs.. I use mono on a big bait caster with a clicker. I fish a lot of fast water though, not so much the stuff with a lot of obstacles. I like below spill ways and...
  13. E

    Tyvek house-wrap under decking and over pour in foam????

    That's a great idea. I think I'll give it a try on my Mako project when I replace the floor. All the foam will more than likely be replaced at that time.
  14. E

    Bow Deck Rubbing on hull - slight detent created

    I'd remove the diagonal brace and leave it out of the equation. Depending on how high the battery sits on the shelf it's now sitting on, I'd put a straight edge across the gunnels and see if you can leave the battery where it is. If it clears I'd mount it where its sitting. You won't gain a...
  15. E

    reliability

    If it were me I'd shop for a 9.9 or 15 for that size boat. Either would make a good fit for it and when you decide to sell it later on there's more people looking for the larger engines versus the 5 horse. Lots of people use them for kickers.
Top