Search results

i used an old trolling motor transom mount removed the shaft , then cut a paddle and put on the trolling motor mount where the shaft connects .

I got it, I didn't have the correct serial # and content # from my unit. Very cool feature, now you can map a lake or pond and have it on you plotter!

I've done all except load the map. I thought it was supposed to load automatically. How do I load the map?

Does anyone know how to use the Gofree maps? I'v recorded and down loaded my own maps & social maps, but can't seem to load onto my Elite 4 HDI?? Do I maybe have to update the software its about 3 years old? Seems like a really cool feature.

Thanks Guys for the advise! Used a my trolling motor battery to test the lights and sure enough it was just a loose ground wire on the trailer.

They are incandescent and no its not a tilt trailer. I'll try running the ground to each light.' thanks

So, I have a 3 yr old loadrite single axle bunk trailer for my 14' jon boat. Plugged the lights into my truck last week to check that lights are working and nothing. Then I tried it on my wife's suv and the lights worked? Drove down to autozone for a light tester and checked my truck and it is...

I have the tracker 1436. No real problems, just the paint chips off easily. The fishing I do is just like you, smaller ponds & lakes, usually alone. So, its suits me fine. Looking at the Alumacraft its 2" wider & 2" longer with storage too. A boat that small every inch helps! Its does weight...

Used 3/4" plywood, treated the plywood with water sealer. Seats have swivels under them. Go as big as your budget will allow you to, the topper is a 1542. Wish I had gone up to the 1542 for the extra $$. A little more room for a few extra $$ would have been worth it! Good luck!

Has anyone put a livewell in the center seat of a 1436? I think that's my next mod? Any help or advise would be appreciated!

Stability is good. The front deck is at water level so its perfect for that boat. I've tried standing on the rear deck & it does get a little tippy. You just have to be aware of how your moving around in the boat. The 9.5hp evenrude is also just right, with just me in the boat I'm hitting 17-18...

Yeah, that's exactly how I have it set up. Works good, but foot control would be better. One problem I'm having is making a mount for the transom mount on the front of the boat. I've almost lost the motor twice, there's a lot a of flex on highest speed. Any ideas?

Thanks, That's just to lay my rods across, with velcro rod holders. Have a very active 6 yr old who loves to fish with me, was afraid he would fall on them & get hurt or break em.

Hello all, Been lurking here now for quite sometime. Just completed my topper 1436. Chose not to deck all the way up to seat, went to the water line instead for some extra stability when I'm standing. Very please with how it came out. May make some small changes as I fish from it more & more...

WOW, thanks! Lots of good info to read through. Anything on water pumps?

Well, had motor running last weekend with my oldest son 19yr 130#. He sat on the middle bench, battery, trolling motor had been moved up front too. Got an extra 2 mph, so 8mph. Was pleasantly surprised! The I get the motor home & put it in a barrel with water to run it again (service man told me...

My last outing the motor wouldn't run? But, last successful run. Yes, seemed to reve good. Mechanic cleaned up & has it running. I'll give another test run?

Got the diagnosis today from the repair shop. Says, cleaned the carbs, changed the gear case oil (which was really bad & may have a leak) & has it running. Next he says, that its over heating. Pump is working ok & could be the thermostat ? So, I'll be heading over to pick it up Friday. We will...

Well, it got worse. Now the motor wouldn't start. So, off to the repair shop I go!

No, my employee who is also a Mechanic checked it for me. Good point on if I fix it & decide to sell it.