Search results

I installed a big tiller on my 90 Yamaha jet. I would like to find a shift cable about 4' long to go directly to the mounting bracket on the jet foot. Does anyone have a part number? This is the closest I have found so far, but I don't know if there is room inside the tiller to use a standard...

For sale is a 10hp Copperhead. I do not know the year but it has low hours. Prop measures 9.75". New bushing and seal in the lower unit. Runs good. Located near Knoxville, TN. My price is $1600. No trades. No shipping. Call/text Andrew at (865) 68four - 881zero.

I fished this out of a used 12 gallon tank that I purchased. Does anyone know if it was originally a part of the tank, and what purpose it serves?

Please see my ad on Craigslist for details. The motor is located in East TN. https://knoxville.craigslist.org/boa/d/evinrude-outboard-jet/6577038253.html

For sale is a Lowe 1652 with a 30hp Johnson jet. The boat is wide open with pod seats in the rear. There is a 12 gallon gas tank mounted behind the front deck and storage in each pod seat. The motor is a factory jet outboard with electric start. It has been recently serviced by a professional...

For sale is 1542 Duracraft jon boat with a 25hp Mercury. The boat is riveted, but has no leaks. It has a nice camouflage paint job, camo swivel seats on sliding rails,removable floors, running lights, and bilge pump. Also included is 44lb MotorGuide trolling motor. The motor is a 25 horse...

I have a 30hp Johnson on a 1652 flat bottom. I finally got the motor height dialed in and now I need to bolt it down. The bolt holes in the transom bracket fall in a bad spot. Any ideas? Just drill them and make sure they are sealed good?

The boat must be picked up in Oak Ridge, TN. I am not interested in any trades. For sale is a 1998 Solid Craft 2070 tunnel hull, 1995 Johnson Fast Strike 115, and galvanized tandem trailer. The boat is all 1/8" plate and has a prop tunnel. The bottom is 70" wide, the beam is 92", and the sides...

I would like to buy a 1452 flat bottom to hang a jet drive motor on. I have cash in hand. Located in East TN. Please call or text Andrew at (865) 68four -881zero. Thanks

For sale is a 1444 Weldcraft with pod seats, 3" jackplate and Bob's tilt/trim. Duralux paint, hydroturf. The hydraulic pump and a small deep cycle are mounted in one seat pod. The motor has 12 hours on it since it was worked on by Mr. Brandon Cantrell. It is rope start, short shaft, with a...

SOLD For sale is a 1999 90hp Yamaha. This motor has no compression on the top cylinder. Otherwise it is in good shape. Located in Oak Ridge, TN. My price is

For sale is a 2006 Delta Waterfowl edition Go Devil long tail mud motor. This motor runs great and is well maintained. I just changed the oil. It has the swivel bracket so you can turn it around. Electric start and rope start work good. I put on a bike brake throttle for better control. The...

For sale is a 1742 Aluma-Weld with a 25hp Mercury. The boat is all welded, and has a livewell in the center bench seat. The motor is a 2005 25hp Mercury. It has recoil start, a stainless prop, a tachometer, and a brand new water pump. The trailer has new bunks, new lights, and a new winch...

I have a 1983 75hp Johnson long shaft with a jet pump. The motor has excellent compression but I believe the #3 rod is making a noise. I would like to replace the motor before it lets go. I have read that the 56 cubic inch motor is better suited for jets. If I find a 1986-1988 OMC 70hp it should...

For sale is a 1996 17ft Bass Tracker with a 1998 90hp Evinrude. This Pro Team 17 Bass Tracker has all aluminum decks, a livewell with aerator, and lots of storage. The carpet has been redone. The trolling motor is a 12v/24v Johnson that works well. There is a new Hummingbird depth finder on the...

I have a 1983 Johnson 70hp with a jet foot. What would be a good size boat to pair with this motor? I was running it on an 1848, but the jet did not work well with the prop tunnel so I am selling it to build the right boat with a jet tunnel. Typical load will be two people with fishing or...

My trailer has 2x4 bunks mounted flat (boat sits on the 4" side). I would like to get away from the carpet and use bunk slicks. In the past I have taken a vinyl porch post cover, ripped it in half on a table saw, and used that to cover a 2x4. I found these boards in Home Depot...

I am putting a trim switch on the end of my OMC tiller handle to operate the factory tilt/trim. The wire will have to run beside the throttle cable in a small gap, so I need to use the smallest wire possible. The overall run will be about four foot in length. What is the smallest gauge wire I...

I have a 1648 with a 70hp tiller motor. I moved the cranking battery up front to help with weight distribution. There is about a 15ft run of 4 gauge cable. I would like to add a fuse at the battery in case something rubs a hole in the insulation of the 4ga cable. What style and size fuse should...

I have a 70lb Minn Kota with the metal transom mount bracket from a 101lb Minn Kota. I hit a stump and ended up bending one of the threaded clamps. Can these be replaced?