Search results

Try napa for the right size plug. the store here carries a wide variety of plugs for all kinds of equipment.

I went with the Anderson plugs, that nowgrn4 on page one mentioned, with all my12 volt electric hoists, winches, and tongue jacks on my trailers. These plugs never even warm up. I have these on my tractor, at my receiver hitches, front and rear, at the batteries themselves, my van has one in...

I decided to go with the sky winch over the normal strap one. I have a safety didn't get a shot of that yet.

the rollers and the ramp material I used for a walk way. I also put the cross piece in thinking to use on bunks.

screwed that post up lol. The old and the new.

well finally got to put some time in on the trailer, It has changed a little from when I started.

Johnson model 4W69B and 4WF69B are the two that I have made in Waukegan,Ill. hope this helps.

This is the set up on my 6hp for the cables and it is wired I believe for a kill switch, I don't know what will hook up to these fitting yet? I plan on putting this on my sport canoe where I can be up front in the rivers. good luck on your build.

Thanks for the quick run down, not to argue but I have two knobs one for hi speed adjustment and a low speed one on the front panel? I, me, couldn't notice any changes turning the adjustment knobs,may not of left it sit at a setting long enough for a change to take place? I don't have a manual...

I got the 4hp suitcase Johnson from 69 running ran good and smooth after sitting all them years. first baby size outboard. I have two 4hp from 69 one straight leg the other a suit case, I'd like to run the straight and haul the suitcase for a spare and I need weight up front anyway so I can...

I got me an idea. It's all heavy wall stuff and I got to put motors someplace safer then on a transom, laying in the camper or boat bottom while transporting them, but is trailers the place for it, ahh I'll weld a hitch on it, and that will tie it to trailers .don't want stuff where it don't...

I am going to up load some pictures while it warms up some outside. This is all in the rough stages it can all be fixed by a weldor with some power tools, paint will cover it all up.

Well it finally warmed up enough I was able to get the back gates opened and the boat out of the back. The sky winch works if you have a strain on it, with no weight or pressure the line will slip, hold the bitter end tight so it can get a bite on the line and it will pull till the line...

I have changed a lot of these set ups to over springs, I didn't see any mention of the bolt that holds the springs together you may have to flip the bolt over to fit in the recess that is used for centering I used small c clamps to hold mine together the undo the bolt flip it around tighten it...

I would use shims and spacers to level trolling motor and leave that bow plate alone, to keep its strength in its shape, light weight, and holds that bow together. that's my 2 cents worth

Rich it has to rotate, no ratcheting, turns only one way and has a release lever. then it will free wheel either way. I bought a couple of these a year or so ago had one on the 10' lone star trailer, took it off because I am letting a buddy use the boat and I was afraid he may mess up, not...

another link to greenfield skywinch as its known https://www.ebay.com/itm/Greenfield-SKYWINCH

I had to wait for warmer day to melt the snow it was 50 yesterday and heading to -20 tonight, Wyoming weather. This is a link to the manufacture of the "skywinch" it has a short video of using this winch. "skywinch" capacity of 350lbs for boats under 18'/1000LBS only, use with 1/2 inch...

Rich this is by no means a replacement for the standard boat winch. a separate bow tie down is required as this is not meant to hold a load, it is only a rope puller. Later I will go trampling through the foot of snow later today and get the name of this devise so it can be looked up properly...

I don't need the steps on this trailer but will put something like that on my Lowes. A foot of snow has stopped me in my tracks. I have had other pressing fix me's to fix before I can get back on this trailer. I now am amassing the items I will need to rig this boat with and I want to take...