TinBoats.net
The original aluminum boat site!
Forums
New posts
Search forums
Blog
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Forums
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Axhammer's latest activity
Help Support TinBoats.net:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Axhammer
replied to the thread
This thing is a can of worms
.
Try a left hand drill bit. Sometimes it will catch and run the broken bolt out…like hitting pay dirt.
Feb 23, 2024
Axhammer
reacted to
airshot's post
in the thread
77 Smoker-craft Bench Seat Mods
with
Like
.
If your finnished items look as good as your cardboard templates, your gonna have a nice lookin boat !!
Feb 23, 2024
Axhammer
reacted to
airshot's post
in the thread
77 Smoker-craft Bench Seat Mods
with
Like
.
Where ever you want it for best balance. Different tanks for different placement. Mine is about 3/4 back what would be between middle...
Feb 23, 2024
Axhammer
reacted to
Makaw's post
in the thread
Remove middle bench.
with
Like
.
Here’s what I did to reinforce the hull after deleting my center bench. Port side braces double as rod holders. Starboard braces...
Feb 23, 2024
Axhammer
reacted to
LDUBS's post
in the thread
Remove middle bench.
with
Like
.
I agree with @airshot . Removing a section out of the middle of the bench works. To get an idea what it might look like, take a look...
Feb 23, 2024
Axhammer
reacted to
LDUBS's post
in the thread
1992 Polar Kraft MVT-1751 with a 1992 Evinrude 60 HP…my first tin boat project
with
Like
.
The transom should be 100% supported by the bunks. The transom should not hang past the end the bunks. It is very normal for the...
Feb 22, 2024
Axhammer
replied to the thread
1992 Polar Kraft MVT-1751 with a 1992 Evinrude 60 HP…my first tin boat project
.
Aye Capt’n … Steady as she goes I’m sure Thill has read this thread, because he has commented along the way. After studying the pic I...
Feb 21, 2024
Axhammer
reacted to
Still Afloat's post
in the thread
1992 Polar Kraft MVT-1751 with a 1992 Evinrude 60 HP…my first tin boat project
with
Like
.
With eyes then we can say, “Aye Aye Capt’n.
Feb 21, 2024
Axhammer
replied to the thread
1992 Polar Kraft MVT-1751 with a 1992 Evinrude 60 HP…my first tin boat project
.
I flipped the boat over and put it on the trailer. I mounted the winch post, for the hand winch. The whole setup looks out of whack. I’m...
Feb 19, 2024
Axhammer
replied to the thread
1992 Polar Kraft MVT-1751 with a 1992 Evinrude 60 HP…my first tin boat project
.
I lowered the front of the bunks on the trailer today. I left the rear brackets at the height I had them. I cut a couple inches off the...
Feb 18, 2024
Axhammer
reacted to
Lowrider1's post
in the thread
Fishing License
with
Like
.
I'm a DV too but only 40% but I still get the old guy rate...$30 for 3 year hunting and fishing, Blessings to all DV's.
Feb 17, 2024
Axhammer
reacted to
LDUBS's post
in the thread
Fishing License
with
Like
.
Son of a gun. My 2023 fishing Lic was $76.94 (including the second rod validation). I can get a lifetime license for $644.50. I'm 71...
Feb 17, 2024
Axhammer
reacted to
Stand Up's post
in the thread
Fishing License
with
Like
.
I just turned 65 and now I don't pay anything. I have to carry my ID to prove my age, but that's it. Nice.
Feb 17, 2024
Axhammer
reacted to
sonny1's post
in the thread
Fishing License
with
Like
.
Just found out that at 65 years old I can get a lifetime fishing license for $15.00 dollars. Had no clue until this morning when I...
Feb 17, 2024
Axhammer
reacted to
airshot's post
in the thread
1968 Richline Jon to Runabout build
with
Like
.
Awesome !!! Thanks for the pics...
Feb 17, 2024
Forums
Members
Top