Search results

The river in the area where we plan to fish is not bad, it has a lot of bends and moves really slow, great place to kayak or tube and most of the time you have to paddle down stream due to such a slow current. No big boats can access due to the ramps are for kayak and canoe loaded and unloaded...

Guys I just bought a 10ft Jon boat looking to use the boat on the Chattahoochee river near my house the area of the river I will be fishing is 1' - 6' deep ALOT of rocks few small shoals . I will only fish when the water is low and slow moving , do you think I can get away running a 55lb thrust...

jr, its a simple deal i took two pieces of 3/8 steel plate cut 12" x 8" and got 12" piece of 1 1/2" square tubing welded the tubing between my two sheets you will have to use a hammer to tap the extender down into place then two 3/8 bolts to hold it and your done. This raised my motor 5" so you...

The guide-on are 1 1/4" pvc I secured it to the trailer with some light weight long ubolts. I will get some close up pics.

After picking up this landau 1436 in December. I have finally got the registration taking care of and the motor issues worked out . I decided yesterday to build a transom extender and now that's done its time to hit the water.

I have a Landau 1436 and has a front & rear deck approx. 3" below the gunnels . I can walk front to back and fish off the front with no issues. I only fish alone or with my 10 yr old son but I have had no problems. I have spent alot of time fishing and poling a Gheenoe Highsider so this...

You have a good foundation to start from in a Tracker, but it would be hard for me to hook that boat up when that 675 sitting next to it is staring me down. :D

they are asking 800 the motor had a complete rebuild back in October. After getting my boat inspected by DNR I cant run the 25hp my boat is only rated for 15. If anyone is interested in this 25 its located in Metro Atlanta. Shoot me a message and I will give you the sellers contact number.

Thanks Russ ,I found one of Craigslist that is completely rebuilt I'm thinking about getting for my 14' jonboat.

Looks good, I've been thinking of camo paint job for my current project.

Can anyone give me the weight of a '72 25HP Johnson tiller with short shaft. I have looked every where and cant find specs for this motor.

Looking for a 9.9 but no luck so far.I know the hooch from whitesburg bridge to the state park really well . my plans are to start fishing the hooch from franklin south during the spring run I don't known that section to good but have a few friends that fish it a lot. I will also fish BT Brown...

1448 . what you see in the pic is how the boat looked when I picked it up. It has electrical already ran with nav lights , bilge pump, trolling motor.

Well Im back in the tin boat club. After running astray for a few years with a Gheenoe I have decided that a tin boat fits my needs better fishing the rocky bottom Chattahoochee River here in Georgia. The boat needs a few things and some TLC but I feel like I have a solid platform to work from.

Ok the State is opening a new park about 7miles from the house The name of the park is Chattahoochee River Bend State Park they plan to open in May . I will finally have a boat ramp to access the Chattahoochee River . I would like to have any and all advice on building a river boat. The river is...

Ok Im up grading my trolling motors on my electric only boat and would like to find a diagram or some info. on wiring everything up. I will have 2 12volt trolling motors on the transom, 12volt motor on the Bow , Lowrance elite 5 fishfinder and a potable livewell/baitwell. I would be thankful for...

I was looking at cutting the middile bench to hide my two batterys but it has foam inside, the boat has three benchs only the middle has foam so, my question is if I remove the foam from the middle should I add foam to the front and rear bench?

Does anyone know where you can buy used or reman. trolling motors? I figure if i go with a used one or reman. maybe I can get a bigger unit for alittle less.

I got some pics uploaded on the 1st post ,so far I have replaced the wood on the transon and added some alum. for protection I carpeted the bench seats and placed the swivel camo seat on to see how it looks the front will not have a pedestal since my son will sit there I plan on 50lb minn-kota...

I recently purchased my first jon boat ,first off the boat is a 14' and 46" not 36" across the top 32" in the floor ,I replaced the wood on the transom and added seats I perfer to run 12 volt trolling motor since the boat will be used in electric only lakes I plan on mainly crappie fishing with...