Search results

Needing a eom prop for my 65 evinrude 6 hp

The boat it's self is very heavy, takes all I got to pick up the back of it without a motor. Not sure the make of the boat but it's 14ft with 3 benches not including the on attached to the bow. The reinforcing ribs are spaced about half the distance normal boats are. Extremely heavy duty...

Here are pictures to as where the motor sits. I have it trimmed all the way down to try and help get the nose down. Since I obviously have not tore anything up I believe the answer is just to go a little slower. But I was all excited about breaking the 10mph barrier. Lol

After some research I do not have a hub to spin. Lol. But I have noticed this, my motor does not have the power to plane out my boat unless I have the battery and fuel tank up front to balance it out and the water is glass smooth. So when the boat does get pretty close to planing out I can hear...

Basically I was running pretty close to full throttle and the motor kinda kicked up and started revving and the boat started slowing down, I backed off the throttle and it was running fine, I throttle up a little and it started doing it again. I was looking back when it happened this time, motor...

Was out yesterday and the motor just took off revving and boat slowed down. Did that a couple times but as long as rpms were low i limped it back in. I was thinking gears, bushings or spun prop. When i removed prop there was a wad of line wrapped around shaft. Hoping thats what it was causing it.

Never mind. Lol. Pulling my hair out with this **** thing. Gonna buy me a new motor when this one quits. But it won't quit, just keeps going.

Please someone tell me that the bolts that hold the propeller housing own are not right-handed threads before I tear something up. Done everything in the world to get him to break loose and they want I guess I hammers next

Got it. Thanks all.

So I think I am gonna get the manufacturers version. Should I go right thru the throat of the carb or mix in the fuel is what I am not sure which way to go. . If I mix in the fuel I need to troll around the lake until I go thru the gallon of fuel I guess. With a 6 hp that will take a while. If...

For some reason I don't trust sea foam. Guess it's the foam part that worries me lol. Is there a certain type for a two stroke or what? Is it just a generic can you get and use for everything?

I am gonna rebuild my carb this winter and basically do a overhaul. What would be the best practice to keep a carb clean year round? I'm thinking a fuel stabilizer, draining the fuel bowl if I'm not gonna be using the boat for more than a few days and I have read somewhere about another...

There is about a 2" hole in each compartment that I was gonna run the line through. That boat is so heavy and then I add me, the fuel tank and battery to the back it struggle for any speed. But then again I am not skiing. Lol

Yeah I was hoping it would be fine, just replaced the lines and bulb. Just have too much crap back there with me, need some room. Thanks

It's a big ole mighty 6 hp with a 3/8 line. I help it along by paddling, only when I'm going uphill though. Lol

I am trying to move some weight to front of the boat, I have a 14ft aluminum and the middle bench had lids that open to 2 compartments. If I move my gas can there it will add an extra 4ft to the current length of the line. Would that cause problems with the fuel flow? Gonna move the trolling...

Was not expecting this, of course I have never disassembled a outboard before. When I removed what I thought were the heads I was expecting to see the top of pistons. Just a dome with a hole for spark plugs. I am guessing that on e I split the crankcase the pistons come out and I just have the...

Well I got it mostly apart, the first look at pistons is a concern. What you think. I am trying to find a new set since I got it torn down but had no luck so far. Any ideas?

I have a 58 gale 5hp in garage, it has not run in a few years. I am wanting to make it a winter project and restore it. Has anyone dealt with one of these before and do you think it would be worth the effort.

Thanks hopefully i didnt tear anything up. The motor is one yearyounger than me and in a lot better shape Maybe i should start drinking oil. Lol