Search results

Where did you purchase the rod tubes in your picture? I haven't been able to find them to look at?

I have a 1652 Sea Ark with factory pods and the same Electronics as you. The factory welded a small plate on the transom very close to the Pod on the Starboard side. It works fine there up to about 10-13 mph. Then it quits functioning pretty much.

I just picked up a new Sea Ark 1652 MV last week. I ordered it to my specs. It has a .125 floor, built in 12 gallon gas tank, light package, tm wiring with a MinnKota SE 55lb TM. Bass seats, electric breaker package, folding lid across the back from the seat to the transom. Gator Hide floor...

I went ahead and ordered a Sea Ark 1648 w/25hp Mercury, trim & tilt. Spay on Liner, Beefed up Bass Seat Plates, tm setup, nav lights, and a couple other small extras.

What brand model of Jack Plate did you use?

I am very close to buying a new grizzly 1648 tiller model w/trailer. I'm wondering what size and brand of motor to buy for it. I live in Florida now and an area lake nearby has a 20hp motor limit. Evinrude has a 15 or 25hp. Yamaha 20 and Mercury 20. Tohatsu I guess the same as mercury. Very...

I asked Jim to post the pictures for me, I can not find them anymore. sorry.

I mounted a mini-jacker on my 2008 grizzly 1448 w/25 hp Mercury. I mounted the top of the mini-jacker even with the top of my transom. My Transom measures 20 inches. My cavitation plate is now a hair above the bottom, not much at all. I think if I wanted to do it over I would mount the...

I do not have any way to tell how fast I'm going. I bought a powertech prop after consulting with them bought the TLR3R11P prop SS. Hard to answer without an GPS.

I just put a TH mini-jacker on my 1448 grizzly this weekend. You have to measure this and when it mounts it pretty permanent. I have a 25 hp mercury on mine and it weighs 157 lbs. I did get the measurements correct and my cavitation plate is even with the bottom of my boat. I don't know how...

I tried moving the motor closer to the transom and that did not help. So I put it back where I had started. My friend could actually just stand up and take a couple of steps and lean on the front deck and that boat would pick up speed and plane out that quick. Then he could sit down and away...

Well, finally after 5 weeks I was able to put my 1448 allweld grizzly in the water. I worked last night and this morning putting on the TH mini jacker. The plate I mounted even with the top of my transom which made the engine 3 inches higher than before. The length on the motor is 22 1/2 a...

Unfortunately, I do not have power T/T with my boat. That's pretty much why I was asking about where to set the cavitation plate before I mount the Jack Plate. Little higher, maybe 1" or even. Your thoughts?

So, when you placed the Jack Plate on the Transom I see where you put the cavitation plate almost even with the bottom of the Hull. Would you or could you have raised the Engine a little higher or does this work just fine as is?

Can anyone comment on their experiencies with putting a TH Mini-Jacker™on a 14 or 15 ft Jon Boat? I will be putting one on my 1448 tracker grizzly SC W/25 hp Mercury EFI.

What motor and prop do you have on this? Does your cavitation plate sit even with the bottom or is it 11/2-2 inches below? thanks

I have the Motor Pin in the second hole nearest to the transom, only 1 more hole. The cranking battery and the fuel tank are in back between the seat and the transom. I have the trolling motor and battery up front. Maybe should move the battery or fuel tank forward if at all possible. The...

I just purchased a 2008 1448 SC W/25 hp El 4S EFI Mercury grizzly tracker. I did not get to try it out before I bought it due to weather conditions. I did get it on the water yesterday and ran it in a small pond, and I never got the boat to get up on plane. Every time I went full throttle...