Search results

Hi Guys is this tongue extension for harbor freight trailers?? thanks. https://www.redtrailers.com/ShowItem.asp?id=SJ85ERN

So I got these folding plastic seats, once you sit on it they lock in the base, how do you get them of the zwiveleze pedestal? the pedestal pops out from the floor stuck to the seat?

Got a couple of stripers in the Hudson today, near Albany. 23 and 24 lbs

I was looking at some real nice combo deals on Boat+Motor+Trailer, my question is this, The Side console models are almost $2500 more then similar tiller type motor+boat What would it cost me to Mod a boat, add a console, cables etc? can you do it to all motors? with a kit? #-o Thanks

Sylvan, Alaskan 13 DLX Split There is a Marina close to me that has these, and very attractive packages, like a 15HP 4 stroke Yamaha + trailer for $ 5500. ! I think I will pull the trigger on one of these next Year, I would prefer a console though... Any body with experience on these?

I am in the process of painting my Fisherman 6, I like to use a close match to the bottom blue color, I like car paints, have used them for other projects, what color would you recomend? Thanks

I need to pick up some screws to attach a seat to base, what is the size and lenght?

Is photo shop a program you download or is it a package you purchase and then load up? Either way I know little about it, would be interested on some opinions./ Thanks

You guys always back up, then go back in the boat and turn around . then shoot for the trailer? I am just asking, I was alone at a small launch today coming back in, after backing up I used the 15 foot rope I have to let it Off, tied it on the bow, pushed the tin back in the water with my foot...

Spend 3 Years aboard the M/S Sagafjord in the early 80th,as a Chef, best time of my life, 3 World cruises etc. Great Tinboat!!!

Did that today , rainy, crappy day etc. $ 25 for extension, $ 8.50 for the hardware!

I got to replace/ remove a roll pin on my starter , replace the platic pinion gear on top, is it as simple as using a plier to remove (its hollow) then re insert new one?

Found that info. How to Use SEA FOAM In Tune-Up of Small 4 Cycle Carbureted Engine Lawn Mowers, Tillers, Edgers, Snowblowers, etc. Start engine. If engine will not start, check spark and compression. If engine has spark and compression, pour a small amount up to 1/2 ounce into the carburetor...

Any tricks on holding the tiller on my 6HP so it wont turn right and shut off?

I got my set of points and condensers for my motor, in the package there is a capsule of grease , like a gelatine pill size, where does that go? on the point shaft?

The information I gathered for the thread size on the three top holes for flywheel removal is either 5/16" - 24 SAE fine x 2 1/8 grade 8 or 1/4 - 20 grade 8. makes sense? I guess i get both sizes, not sure where though, Home depot dont carry it around here....

So I got this fisherman 6, , has been sitting for a while. Compression is 62psi and 61 psi good right? changed plugs .30 gap, gas 50: 1, nothing happen , no spark or cough or anything, checked the gas filter screen clean, looks like gas goes there, I guess I need some kind of start up kit, any...

I want to install a small bilge pump in my jon, you just leave them sitting on the floor? Is there a way to drill the screen to the floor without going thru the bottom, I got this transom brace, maybee an L aluminum bracket as low as possible, then install the bilge. makes sense? or are there...

I search a bit for opinions on battery chargers, what are you guys using? and where did you get them, I have a 12 v setup. Thanks

One of the things we have up here are smaller ponds with out regular launches, I like kayak fishing but it cramps my style a bit... anyhow if I can park close to the water, I slide the boat off the trailer, load up, and go, mostly electric, but also with oars. I have no problems paddling. Coming...